Tuesday, 6 May 2014

Yankee Tank progress

HR54 Yankee Tank. Inner side tanks in place.


Progress on my HR Yankee Tank has been less than spectacular, as I mentioned in an earlier post, I'm treating the kit simply as a starting point in my quest for a scale model of a Yankee Tank, so to this end I've re-made some of the parts rather than use those in the kit, which is a time consuming method of progress. My mate Bob Goodyear, in nearby Dumfriesshire, has a lathe; he turned me a set of frame spacers which are designed to temporarily hold the frames in position while nickel silver spacers are soldered permanently in place, these are 25.5mm wide and will result in an overall width of 26.9mm for the frames providing negligible side-play on the driving wheels. The rear axle will be rigid and carry an ABC Mini Gooch gearbox fitted with an M1824 motor mounted upright that should just allow space for a small flywheel. The front driving axle will be sprung and the bogie pivot point will be solid to provide three-point suspension.

Several apparent similarities between the Yankee Tank and the Adams Radial Tank were pointed out to me by Sandy Harper which prompted me to compare drawings of these engines. I found a drawing of the Adams engine in J N Maskelyne's "Locomotives I have Known" and realised while perusing this that the inside valve gear was not only Stephenson's in both cases but also that the works from the Adams engine should fit the Yankee Tank. I promptly ordered a set of Adams valve gear from Martin Finney,who sells this item as a separate kit. The space between the frames beneath the Yankee Tank's boiler is very visible and I think Martin's finely engineered kit of parts should fill it nicely.

The boiler itself is 4' 3" diameter according to my drawing and this is the diameter I made it despite reading in Cormack and Stevenson that the maximum diameter of the boiler was a quarter inch under four foot. I presume this latter misleading measurement to be without the cladding.

I've added window surrounds inside the cab front and rear plates (a necessity rather than a luxury) using Geoff Holt's method, which I derived from his recently published book on locomotive modelling.

My next next task is to get the engine up and running and first of all I need to address the coupling and connecting rods, which need to be re-made...



            

Tuesday, 8 April 2014

HR OCT and Chummy.

HR d.47 OCT with Austin 7 Chummy c.1923

The Austin 7 Open Tourer known affectionately as a "chummy" was in its first year of production in 1923 and here's one being delivered by the Highland Railway on an Open Carriage Truck. The car's number plate begins with SO... the S being for Scotland and the second letter denoting the area, in this case Morayshire. The wagon plate lettering reads silver rather than white and as I couldn't dry brush it to read white, I relied on the weathering to simply dull the metallic lettering which I hope works. On Saturday the model's bound for Carlisle to the CD0GG meeting, for a run on the layout, a few photos in the scenic section and entry into the annual modelling competition.

Thursday, 27 March 2014

HR Yankee Tank Project

HR Yankee Tank 4-4-0T front bogie.

My Yankee Tank kit arrived from Lochgorm Kits a couple of weeks ago and though I've not made a great deal of progress yet I have been able to assess the merits, limitations, omissions and faults of the kit which will be evident as description of the build progresses. I've no doubt that the kit built straight from the box produces a reasonable Yankee Tank, however my intention is to use the parts provided by the kit as the starting point of a fully detailed scale model of the engine based on available photos and the drawings in Peter Tatlow's invaluable "Highland Locomotives". For the prototype my choice lit on HR 14, built in 1893 and renumbered 54 in 1900 and it is in this latter guise that I'll build her. There is a superb photo extant of the engine as HR14 which provides most of the information I need to supplement the drawing.

The bogie illustrated has been built using the parts supplied with some modification, in particular I had to adjust the width of the spacers. An 0.7mm washer outside each axle box allows the wheels to revolve freely without fouling the centrally mounted bogie spring which protrudes beyond the frames slightly. I'm not sure what effect widening the bogie frames will have on the loco main frames which are I think rather narrow at a bare 26.4mm overall and may need wider spacers in turn.

 I will sign off for now as I need to order some scratch building materials!



 


   

HR Fish Truck

HR Fish Truck from a Lochgorm Kit

I decided to build this wagon in a short interlude between loco projects which presented itself before the Glasgow Show in February where I intended to buy a "Lochgorm" Yankee Tank kit which I knew, once started, would be a time consuming project and leave little time for this kind of indulgence. It's a Jones Open Fish Truck d.12 and is the second I've built to add to my Highland Railway train of mixed goods and passenger stock. However, whereas the first was finished in HR passenger green livery I intend the second, as there is much uncertainty about the actual colour of these vehicles, to take to the rails in goods wagon oxide. It needs a few more details to complete and an interesting and appropriate load of the fishy kind to bring it to life. I'm considering the possibilities... 

Thursday, 20 February 2014

A NW Tender in search of an Engine.

LNWR 1800 gallon tender c.1885
 
The 1800 gallon tender was introduced to the LNWR by F.W. Webb in 1874. From 1882 these tenders were built with a single side plate 14ft long in place of two shorter ones and it is this version that is the subject of the "Gladiator" kit which was the starting point of this model. At this point in time it remains a tender in search of a locomotive. However... there is a suitable locomotive kit in the pipeline and a good deal of development work has been done already, and though it's still under wraps...watch this Blog for news of developments.

 
LNWR 1800 gallon tender c.1885

Some additions and improvements were made to the basic Gladiator kit, the tool boxes and their plinths were a particular trial and took a good deal of work before they were acceptable. The handle below the spoked brake wheel operates the water scoop which I have yet to model.




It's a busy place underneath an 1800g tender.

The outer brake pull-rods can be disassembled to enable removal of the wheels. The outer rods are held in place by 14BA screws which pass through spacing tubes and thread into the rear pull rods which are soldered to the inner chassis and tapped to accept the screws. The bushes carrying the center axle slide in a vertical slot and are sprung by a wire attached to the chassis, otherwise the suspension is solid. The tender is arranged for the American pick-up system by having the wheels on one side shorted out.

Thursday, 30 January 2014

A Crew for HR 57

On the footplate of HR57, this pair were the inspiration for my own crew c.1895
 
 The driver on the left of the picture has a "drivers cap", possibly issued by the HR though it's the only cap of this style I've ever seen in a photo. Neither figure displays any other uniform item of dress, like most working men of the period, both driver and fireman are wearing their own working clothes. The light coloured jacket of the fireman may be of unbleached linen similar to the fatigues worn by the lower ranks of the army in barracks when on work detail, the so called "Regimental Sports", which involved getting the coal in and suchlike.


HR 56 shunting at Perth in Highland Railway days c.1920

The pose of this figure was the inspiration for my own driver (below) and is eminently suitable for a shunting engine. This is a rather later photo than the one above and the driver now has a uniform cap, his overalls and jacket are presumably his own working clothes.


Heroes of the Footplate : Driver for a Stroudley Tank Ref: R.23


The miniature driver at work on the footplate of my own model of "Lochgorm". Both the driver and fireman are designed to fit nicely into the cabs of a wide range of shunting engines, not just HR Stroudley Tanks, they'll fit just as well into that more famous Stroudley engine, the LBSCR Terrier.  The colours I have used are those I think most probable judging from the tonality of the two b/w photos above. Below you can see both figures in the cab... I think their contrasting poses work well together. Ref: www.borderminiatures.com




Heroes of the Footplate : Fireman for a Stroudley Tank  Ref: R 24







 

Wednesday, 22 January 2014

HR d.47 Open Carriage Truck with load.

HR d.47 OCT with Austin 7 Chummy.
 





The Austin 7 Open Tourer was introduced in 1923 and became known as the "Chummy". The white metal kit for the car came from South East Finecast and was the earliest car kit I could find. The spokes of the wheels are etched nickel silver and really set the model off well. The only addition I made to the kit was a gear lever and some blobs of glue for headlights. The car would have been secured on the wagon with wedges under each wheel. In addition there may have been straps or ropes from the side rails too as suggested by the photo on page 79 of "Hunter".

I made a master pattern for the springs and cast a set as I couldn't work with those in the kit; the axleboxes needed only a little modification before the springs sat comfortably on top of them. The retaining cross rails were made from square section metal with reference to fig 35 in "Hunter" as were the little chains that hang from the brake lever guard. Vaccum pipes and Westinghouse pipes are from my own castings. I added a Westinghouse cylinder and a vaccum cylinder with their linkages all of which make for a busy and interesting model.

The inspiration for this model came from the frontispiece to Tatlow's "A History of Highland Locomotives" which shows Inverness Station in the early 1900s. In the centre of the picture is an OCT, probably a d.47, carrying a car of the period which I cannot identify. The rear cross rail of the OCT seems to be tight against the rear tyres of the car and there may be additional restraint in place though I can't make out any detail of straps or other retaining devices, nor for that matter can I see any wedges, though I'm sure there's one on the deck of the OCT in "Hunter". I suspect more could be learned if the original photo could be studied rather than a scanned reproduction in a book. Perhaps Peter Tatlow's eagerly awaited and soon to be published "Highland Railway Wagons and Carriages" will add to our knowledge of these fascinating wagons.